ADIC FCR200 Specifikace Strana 67
- Strana / 140
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
General SCSI Configuration 5-5
When connected to a Fibre Channel Switch, the FCR200 is
identified to the switch as a unique device by the factory
programmed World Wide Name (WWN). No further
configuration is needed, although the WWN can be
configured to a user-defined value through the configuration
interface.
General SCSI Configuration
The FCR200 appears on each SCSI bus as a single initiator. The
default initiator ID is 7, and can be set via configuration to any
valid SCSI address. No other devices on the SCSI bus may use
this address.
The FCR200 provides the capability to reset the SCSI buses
during the boot cycle. This allows the devices on a SCSI bus to
be in a known state. Configuration allows this feature to be
enabled or disabled. This feature is enabled in the default
configuration.
The FCR200 negotiates for the maximum values for transfer
rates and data width on a SCSI bus. If an attached device does
not allow the full rates, the unit will use the rates negotiated
for that device. Negotiation is on a device specific basis, so the
unit can support a mix of device types on the same bus.
Fibre Channel Host to SCSI Target
Configuration
This section describes the configuration of the FCR200 when
acting as a target to a Fibre Channel Initiator, passing FCP
requests through to SCSI target devices.
This is configured as the default, using soft addressing on the
Fibre Channel loop and auto addressing for the target device
mapping. Auto addressing is described further in this section.
The FCR200 automatically detects if it is connected to a loop
or a switch, and will use the appropriate type without further
configuration.
Address Mapping
The FCR200 supports three addressing methods for mapping
SCSI targets to Fibre Channel Hosts:
Indexed Addressing Allows you to edit and maintain a
static address mapping table.
- Operator Guide 1
- Copyright Notice 2
- Copyright Notice (Europe) 2
- Contents 3
- Configuration 6
- Troubleshooting 7
- Ethernet Assignments 8
- Reference Standards 9
- 62-9301-01 10
- Introduction 15
- 1-2 Introduction 16
- Overview 17
- Intended Audience 17
- Organization 17
- Associated Documents 18
- Notice (US Only) 19
- IEC Statement (Worldwide) 19
- European Union Notice 19
- VCCI Statement (Japan) 20
- Description 21
- 2-2 Description 22
- Introducing the FCR200 23
- FCR200 Features 24
- FCR200 Specifications 25
- FCR200 Benefits 26
- Multiple Initiators 27
- How the FCR200 Works 28
- Channel Device 29
- Processing SCSI Information 30
- 2-12 Description 32
- 3-2 Safety 34
- Safety Instructions 35
- Grounding 35
- Servicing 35
- Warranty 35
- German Statements 36
- Sicherheitshinweise 36
- Schutzerdung 36
- Wartung/Instandsetzung 36
- Laser Safety 37
- Class 1 Laser Product 38
- Laser Klasse 1 38
- Luckan 1 Laserlaite 38
- Product Information 39
- Usage Restrictions 39
- 3-8 Safety 40
- Installation 41
- 4-2 Installation 42
- Installing the FCR200 43
- Location 43
- Unpacking the Box 44
- Mounting the FCR200 in a Rack 44
- Required tools: 45
- Installation Procedure 46
- Installation Procedure 4-7 47
- 4-8 Installation 48
- Installation Procedure 4-9 49
- 4-10 Installation 50
- Interfaces and Connections 51
- Fibre Channel Connection 52
- Fibre Channel Connection 4-13 53
- 4-14 Installation 54
- SCSI Connection 55
- 4-16 Installation 56
- Ethernet Connection 57
- Serial Port Connection 58
- Autobaud Feature 59
- Connecting the Power Cord 60
- Information 62
- Understanding 63
- Understanding the FCR200 65
- Soft Addressing 66
- Hard Addressing 66
- General SCSI Configuration 67
- Address Mapping 67
- Indexed Addressing 68
- Auto Addressing 69
- SCC Addressing 70
- 6-2 Configuration 74
- Configuring the FCR200 75
- Operation Indicators 76
- Host Device Configuration 77
- Device Management 77
- Communicating with the FCR200 78
- Setting Up Serial Port 79
- Communications 79
- Power Up Menu 80
- Power Up Menu 6-9 81
- Perform Configuration 82
- Baud Rate Configuration 83
- Fibre Channel Configuration 83
- SCSI Configuration 84
- Ethernet Configuration 85
- Mapping Mode 86
- Trace Settings Configuration 87
- Save Configuration 87
- Display POST Status 88
- Download Firmware 90
- Download Firmware 6-19 91
- 6-20 Configuration 92
- SNMP Configuration 93
- GET and SET Community Names 94
- IP Address for Traps 94
- Trap Priority 94
- 7-2 Troubleshooting 96
- Indicators 97
- Basic Verification 98
- Verify SCSI Devices in NT 99
- Verify Configuration 100
- Verify Addressing 100
- Verify Devices 100
- Verify Host Configuration 100
- Contact Customer Support 101
- 7-8 Troubleshooting 102
- Assignments 103
- Ethernet 103
- A-2 Ethernet Assignments 104
- Function 106
- Fibre Channel 107
- Interface and 107
- Commands 107
- Download Command 109
- Report LUNs Command 111
- PRLI Data 112
- Read XFER_RDY Disabled 0x1 113
- Write XFER_RDY Disabled 0x0 113
- SCSI Interface 115
- SCSI Interface and Commands 117
- Logical unit addressing 118
- Addressing 119
- Structures, and 119
- Operation 119
- SCC Addressing Option 123
- Indexed Addressing Option 124
- Reference 127
- Standards 127
- E-2 Reference Standards 128
- E-4 Reference Standards 130
- Glossary 131
- 62-9301-01 132
- Glossary gl-3 133
- Mapping Table POST 134
- Glossary gl-5 135
- SNMP World Wide Name (WWN) 136
- Index in-3 139
Magic Chef MCB780W - 2 manuales
Manuales del propietario y guías del usuario para Microondas Magic Chef MCB780W - 2.
Ofrecemos 1 manuales en pdf Magic Chef MCB780W - 2 para descargar gratis por tipos de documentos: Especificaciones
Magic chef MCB780W - 2 Especificaciones (21 paginas)
Marca: Magic-chef | Categoria: Microwaves | Tamaño: 9.57 MB |
Tabla de contenidos
Más productos y manuales para Microondas Magic Chef
| Modelos | Tipo de documento |
|---|---|
| MCD770ST1 |
Manual de instrucciones
Magic Chef MCD770ST1 Instruction manual,
19 paginas
|
| M21-3 |
Manual de usuario
Use & Care - Whirlpool Shopping Cart,
10 paginas
|
| MCM990W |
Manual de instrucciones
Magic Chef MCM990W Instruction manual,
16 paginas
|
| MCD991R |
Instrucciones de operaciones
Magic Chef MCD991R Operating instructions [en] ,
45 paginas
|
| MCO160UBF |
Manual de usuario
Magic Chef MCO160UBF User`s manual,
54 paginas
|
| MCD992R |
Instrucciones de operaciones
Magic Chef MCD992R Operating instructions,
46 paginas
|
| MCM1310B |
Manual de usuario
Magic Chef MCM1310B User`s manual [de] [en] [es] [fr] [nl] ,
20 paginas
|
| M21-3 |
Manual de usuario
Phone 77 or 78 - NYS Historic Newspapers,
1 paginas
|
| MCP13E1ST |
Manual de usuario
Dashboard,
6 paginas
|
| MCO2212ARW |
Instrucciones de operaciones
Magic Chef MCO2212ARW Operating instructions,
40 paginas
|
| O160 |
Manual de usuario
Tamaulipas, ejemplo de valor: Poiré,
40 paginas
|
| MCM770W/B |
Manual de usuario
Microwave Oven Warranty,
2 paginas
|
| MCD1110ST1 |
Instrucciones de operaciones
Magic Chef MCD1110ST1 Operating instructions,
22 paginas
|
| MCM1310B |
Manual de usuario
Magic Chef MCM1310B User`s manual,
45 paginas
|
| MCD1311ST |
Especificaciones
Magic Chef MCD1311ST Specifications,
28 paginas
|
| MCO165UW |
Guía de instalación
Magic Chef MCO165UW Installation Guide,
8 paginas
|
| MCM1110W |
El manual del propietario
Magic Chef MCM1110W Owner's Manual,
36 paginas
|
| MCM1110ST |
El manual del propietario
Magic Chef MCM1110ST Owner's Manual,
36 paginas
|
| MCM990ST |
El manual del propietario
Magic Chef MCM990ST Owner's Manual,
36 paginas
|
| MCD993B |
El manual del propietario
Magic Chef MCD993B Owner's Manual,
44 paginas
|
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.018 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce